B500 Logo
Slot Car Bracket Drag Racing

Library Old Articles
Projects on Bracket500
Chat Room Mondays
Instructional Links
World Tribute Car
Spec Cars
All Car Galleries
Slip Joint 101
Front Page
Contact Bracket500
Message Board

You are not logged in. Would you like to login or register?

8/09/2013 8:58 pm  #1

My New "Outlaw" Mustang

I know Mustangs are like bellybuttons, but I'm a Ford guy, so.....


It's a bit heavier than I would have liked, but I still have to cut the axle and there's a few things I can trim up to lose a few grams.... 


Anyways, got to make a few shakedown passes, it runs really good......  Best 60' was .087 and the mph was in the mid 90 mph range......



Last edited by Gary Lum (8/09/2013 8:59 pm)


8/10/2013 8:01 am  #2

Re: My New "Outlaw" Mustang

Looks real nice Gary all these *ord s are given me acid reflux LOLhttp://cdn.boardhost.com/emoticons/devious.png

Just enjoying Life and Slots

8/10/2013 10:20 pm  #3

Re: My New "Outlaw" Mustang

Hey Marty,

It's my "little" motor....  http://cdn.boardhost.com/emoticons/wink.png
  It's Timmy's thick neos with a .459 diameter Pro Slot 7/4 arm....  Nothing really special, mags not shimmed, just centered and epoxied in place, bearings on both ends, shunted, reworked Camen regular springs and Golddust brushes.... I think this is gonna be the last go round for this arm, it's been to Alpha twice for balance and the com is .184.....

The body is solid in the front, but floats in the rear...  Not much side to side, maybe .002 but enough to move up and down the same....  It seems to work decent so far.... 

I have a little work to do, take a look at the passenger side braid (left in the pic)....  I got a bit rushed and didn't fluff the end out like normal, but it welded the tip slightly and left a weird burn mark right above......

Roy, try Pepto Bismo.....  http://cdn.boardhost.com/emoticons/tongue.png

     Thread Starter

8/11/2013 11:24 am  #4

Re: My New "Outlaw" Mustang

It was fast.... http://cdn.boardhost.com/emoticons/grin.png
  You're within a few numbers on the .6 side....  .612 was the best pass.... 

.082 but not stuffed.....

     Thread Starter

8/11/2013 3:59 pm  #5

Re: My New "Outlaw" Mustang

How Much glue did it take?


8/11/2013 8:37 pm  #6

Re: My New "Outlaw" Mustang

stretch wrote:

How Much glue did it take?

A LOT!!!  Not as much as I thought though...  I think I could prep and fire it down in 2 minutes though...

     Thread Starter

8/11/2013 8:38 pm  #7

Re: My New "Outlaw" Mustang

Marty, I build em to crash....  If they make it all the way down, it's usually fast....  LOL!  http://cdn.boardhost.com/emoticons/tongue.png

     Thread Starter

8/12/2013 4:50 pm  #8

Re: My New "Outlaw" Mustang

Koford drag...  I'm not proficient enough to mix consistently....  I think a mix would let me run less...  Oh man...  Wish I has some Bogg.....

     Thread Starter

9/11/2014 2:42 pm  #9

Re: My New "Outlaw" Mustang

Wow that looks good. I have a question though. I'm new to slot cars. I've been looking around for a foxbody body but I have a hard time tracking one down. Did you make it?


9/12/2014 12:10 pm  #10

Re: My New "Outlaw" Mustang

Gary that your frame? How bout a chassis pic body off.


Board footera


Powered by Boardhost. Create a Free Forum

B500 Logo
Return to Main

WRP Products

Return to Main
Click on banners to see catalogs
Copyrights reserved ©2014